Wade Shaddy
Wade Shaddy specializes in hardwood furniture, trim carpentry, cabinets, home improvement and architectural millwork. Shaddy has worked in home building since 1972. He has also worked as a writer, publishing in national publications since 1992, including two years as a contributing writer for "Bicycling Magazine," writing on fitness, training and bike maintenance. Shaddy published a novel, Dark Canyon, in 2008.
View my portfolio
By Wade Shaddy, eHow Contributor
Cabinet re-sizing is not uncommon. Often it's prompted by the installation of a taller refrigerator or the addition of a microwave or range hood. Cabinet installers shorten cabinets all the time to accommodate changing situations. Cabinets are no more than plywood boxes, and most can be changed readily. The process of shortening cabinets typically involves cutting out a section and cutting down doors to fit the shortened cabinet. Changes in cabinet dimensions can be done with a table saw. When done with care, the changes are almost imperceptible.
Things You'll Need
Drill/driver
Straightedge
Masking tape
Rubber mallet
Table saw
Hammer
Pin nailer
1 1/4-inch pin nails
Staple gun
3/4-inch staples
Miter gauge
3/16-inch drill bit
Pocket-hole jig
Wood glue
1 3/4-inch screws
Clamps
Putty crayon
Instructions
Re-sizing the Cabinet
- 1
Unscrew and remove the screws securing the doors to the cabinet with a drill/driver. If the cabinet has a shelf and it's removable, remove it.
- 2
Draw a line around the cabinet using a straightedge, on all four sides indicating the cut line -- the place where the blade will pass through the cabinet. Place masking tape centered over the line. Draw an identical line on the tape for reference. The tape prevents veneer from chipping.
- ', image: '',flash: ''}, google_image_size : '300x250'});
- 3
Unscrew screws securing the face frame to the cabinet on the inside and remove them. Use the rubber mallet to bump the face frame off the cabinet.
- 4
Set the blade of a table saw to 3/4 inch in height. Place the cabinet on the table saw face up. Slide the cabinet and fence together to the left or right as needed to align the blade with the pencil mark on the tape. Lock the fence.
- 5
Push the cabinet across the blade with the help of an assistant. Turn off the saw. Rotate the cabinet a quarter turn at a time and repeat cutting each side.
- 6
Tap the bottom out of the cut-off piece with a hammer. Remove the pin nails with diagonal pliers. Position the bottom in the cut-down cabinet. Shoot four, 1 1/4-inch pin nails through the sides to secure the bottom to the cabinet. Shoot 3/4-inch staples through the back to secure it.
- 7
Measure the width of the horizontal piece of face frame -- also known as a rail -- at the bottom of the cut-off piece. The measurement will likely be 1 1/4 to 1 1/2 inches. Subtract the measurement from the setting on the fence. Cut the rail or bottom of the face frame off at the measurement with the table saw and miter gauge.
- 8
Unscrew the screws securing the two small vertical pieces, also know as stiles, of the cut-off piece -- the 90-degree pieces -- of the face frame and remove them. If the cabinet has a center stile, remove the screws from it too.
- 9
Drill two angled holes with a 3/16-inch bit and pocket-hole jig, through the vertical pieces or stiles at the bottom on the inside of the face frame. Apply glue to the ends where you drilled the holes. Use 1 3/4-inch screws to re-attach the horizontal rail to the vertical stiles with the drill/driver.
- 10
Place the cabinet across two sawhorses face up. Apply glue to the cut-off cabinet. Place the face frame on the cabinet. Shoot four 1 1/4-inch pin nails through the face frame, one at each corner. Apply clamps around the perimeter. Remove the clamps when the glue is dry. Place the shelf back in the cabinet if you removed it.
Re-sizing the Door
- 1
Cut the cabinet door in half, perpendicular to the length with the table saw.
- 2
Remove the hardware from the door with a drill/driver. Measure the length of the shortened cabinet. Subtract the difference between the door length and cabinet length. Set the table saw at the measurement.
- ', image: '',flash: ''}, google_image_size : '300x250'});
- 3
Run the bottom half of the door through the saw. The fresh-cut edge should be against the fence.
- 4
Drill two holes through the vertical sides of the top half of the cabinet door. Use the pocket-hole jig to drill the holes evenly spaced, to penetrate through the bottom of the fresh-cut end.
- 5
Insert 1 3/4-inch screws in the holes. Apply glue to the bottom piece of the door. Reattach the bottom half of the door by driving in the screws with the drill/driver.
- 6
Measure the hardware placement on an existing door. Use the measurement to reinstall the original hardware to match existing doors. Fill the previous screw holes with color-matched putty crayon.
- 7
Screw the top hinge back onto the door using the screws that you removed. Screw the bottom hinge back onto the door using the same spacing as the top hinge. Screw the door back onto the cabinet. Fill the saw marks with a color-matched putty crayon. Screw the door back onto the cabinet using the original screws.
- 1
- ',image: '',flash: ''},google_image_size : '336x280'});AdblockPlus.detect(function(usesABP) {if (usesABP) {googleAds.overrideAd('GoogleAdsense336x280', { google_ad_channel: 'home_building_remodeling,text,suggested4,Art6' });} });
How to Shorten a Kitchen Cabinet | eHow
Unscrew and remove the screws securing the doors to the cabinet with a drill/driver. If the cabinet has a shelf and it's removable, remove it.
How to Cut Down Kitchen Cabinets | eHow
Measure the kitchen cabinets you wish to cut to accommodate the new appliance. The most important measurements are the height and depth. If the appliance
How to Shorten the Cupboards Above a Microwave | Home ...
How to Shorten the Cupboards Above a Microwave; How to Shorten the Cupboards You can shorten any cabinet without removing How to Remove and Replace Kitchen
Kitchen Cabinet Door Shortened for Taller Appliance
Options to Kitchen Refacing; Kitchen Cabinet Door Shortened for Taller Appliance. The biggest problem is solved when we shorten the cabinet doors or drawers
How to shorten a kitchen cabinet | eHow UK
How to shorten a kitchen cabinet. By using the eHow.co.uk site, you consent to the use of cookies. For more information, please see our Cookie policy.
Woodworking tips- How to cut a cabinet door
Flavia Teixeira wishing eveyone a HAPPY NEW YEAR and giving some tips of how to Cut a door cabinet using OZITO UNIJAW and a makita circular saw system. For
How to Resize Cabinets : How-To : DIY Network
DIY Network explains how to resize cabinets to improve storage. HGTV; I Hate My Kitchen bottom and any shelves from both cabinets. Cut from the back.
Can I Cut Down a Cabinet Without Taking It Down? | eHow
By Shane Grey, eHow Contributor How to Cut the Cabinet to Size for a Fridge; How to Shorten a Kitchen Cabinet.
How to Shorten an Upper Hood Cabinet So A Microwave Will Fit
How to change hood cabinets, shorten cupboards so microwave will fit. Its possible to shorten a hood cabinet so an over the stove Designing Kitchen Cabinets;
How to Build a Cabinet : 15 Steps (with Pictures) - wikiHow
Have you ever wondered how you could build your own cabinets for your kitchen, You will want to cut two of these pieces per cabinet for wall cabinets. 4.
Travelling is my life
ConversionConversion EmoticonEmoticon